Remote Start Keyless Entry Model 5101Installation Guide This product is intended for installation by a professional installer only! Attempts
10© 2008 Directed Electronics. All rights reserved.Component locations and finding wires For detailed information on where to locate components, and ho
11© 2008 Directed Electronics. All rights reserved.➤ Primary harness (H1), 12-pin connectorH1/1RED/WHITE (-) 200mA TRUNK RELEASE OUTPUTH1/2RED (+)12v
12© 2008 Directed Electronics. All rights reserved.There are three harness connections relative to remote start function, including the heavy gauge an
13© 2008 Directed Electronics. All rights reserved.➤ Remote start auxiliary output, 5-pin1PINK/WHITE (-) 200mA FLEX RELAY CONTROL OUTPUT2ORANGE (-) 20
14© 2008 Directed Electronics. All rights reserved.Wire connection guides➤ Primary harness (H1)H1/1RED/WHITE (-) 200mA TRUNK RELEASE OUTPUTWhen the sy
15© 2008 Directed Electronics. All rights reserved.H1/3BROWN (-) HORN OUTPUTThis wire supplies a (-) 200 mA output that can be used to honk the vehicl
16© 2008 Directed Electronics. All rights reserved.H1/5BLACK (-) CHASSIS GROUNDWe recommend that you do not use a factory ground. Ground all your comp
17© 2008 Directed Electronics. All rights reserved.H1/7BLUE (-) FACTORY HORN INPUT*This optional input can be wired to the factory horn honk output of
18© 2008 Directed Electronics. All rights reserved.H1/9BLACK/WHITE (-) 200mA DOME LIGHT OUTPUTConnect this wire to the optional dome light supervision
19© 2008 Directed Electronics. All rights reserved.H1/11WHITE PARKING LIGHT OUTPUT This wire should be connected to the parking light wire in the veh
Bitwriter®, Code Hopping™, Doubleguard®, ESP2™, Fail-Safe®, Ghost Switch™, Learn Routine™, Nite-Lite®, Nuisance Prevention® Circuitry, Revenger®, Sile
20© 2008 Directed Electronics. All rights reserved.➤ Auxiliary harness (H2) H2/1LIGHT GREEN/BLACK (-) 200mA FACTORY ALARM DISARM OUTPUTThis wire sends
21© 2008 Directed Electronics. All rights reserved.H2/3WHITE/VIOLET (-) 200mA AUX 1 OUTPUTThis wire provides 200 mA programmable output whenever the t
22© 2008 Directed Electronics. All rights reserved.Latched, reset with ignition: Similar to the latched output, this type of output •turns On the firs
23© 2008 Directed Electronics. All rights reserved.Note: A 1-amp diode must be installed in line on the factory wire between the wait-to-start indicat
24© 2008 Directed Electronics. All rights reserved.➤ Heavy Gauge, 8-pin connectorThere are 8 heavy gauge wires coming from the large 8-pin connector.
25© 2008 Directed Electronics. All rights reserved.H3/7PINK/BLACK FLEX RELAY INPUT 87A key side (if required) of FLEX RELAYThis wire is used when an
26© 2008 Directed Electronics. All rights reserved.➤ Remote start input - 5-pin connector1BLACK/WHITE (-) NEUTRAL SAFETY SWITCH INPUTConnect this wire
27© 2008 Directed Electronics. All rights reserved.4GRAY N/O or N/C (-) HOOD PIN SWITCH INPUTThis wire MUST be connected to a hoodpin switch. This inp
28© 2008 Directed Electronics. All rights reserved.➤ Remote start auxiliary output, 5-pin These signals are provided to drive additional optional rela
29© 2008 Directed Electronics. All rights reserved.➤ Door lock wire diagramsImportant: Depending on the vehicle, the door locks may be con-trolled by
ContentsWarning! Safety first ...5What is included ...
30© 2008 Directed Electronics. All rights reserved.Neutral safety switch interfaceSome vehicles do not have an electrical neutral safety switch. Inste
31© 2008 Directed Electronics. All rights reserved.Plug-in LED and valet/program switchThe LED and valet switch are incorporated into the control cent
32© 2008 Directed Electronics. All rights reserved.Tachometer settings➤ Virtual tachTo program Virtual Tach:After the install is complete, remote star
33© 2008 Directed Electronics. All rights reserved.➤ Tach learningTo learn the tach signal:1. Start the vehicle with the key.2. Within 5 seconds, pres
34© 2008 Directed Electronics. All rights reserved.➤ Tach threshold On/OffIn most cases, this jumper can be left in the Off position. Some new vehicle
35© 2008 Directed Electronics. All rights reserved.Setting the light flash polarityLight flash (+) / (-) polarityThe internal fuse is used to determine
36© 2008 Directed Electronics. All rights reserved.Remote control Learn Routine™The system comes with two 1-way remote controls already programmed to
37© 2008 Directed Electronics. All rights reserved.The Valet/Program switch, plugged into the blue port, is used for programming. There is a basic seq
38© 2008 Directed Electronics. All rights reserved.Step Function1Auto Learn Standard Configuration (default)The auto learn configuration will automat
39© 2008 Directed Electronics. All rights reserved.Remote control configuration➤ 1-way remote controlA U XNote: If Keypad Lock is On, press and then
Menu 2 - Convenience ...44Menu 3 - Remote start ...
40© 2008 Directed Electronics. All rights reserved.Additional system featuresFor information about Valet mode, Remote starting the vehicle, Manual tra
41© 2008 Directed Electronics. All rights reserved.Select a Feature. Press and release the Valet/Pro-3. gram switch the number of times c
42© 2008 Directed Electronics. All rights reserved.To access another feature in the same menu:Press and release the Valet/Program switch the number of
43© 2008 Directed Electronics. All rights reserved.Feature menusDefault settings are indicated in bold type.➤ Menu 1 - Keyless entry Menu Item Feature
44© 2008 Directed Electronics. All rights reserved.➤ Menu 2 - Convenience Menu Item FeatureOpt. 1Opt. 2 Opt. 3 Opt.4 Opt. 5+1One-time BypassOffOn2 Val
45© 2008 Directed Electronics. All rights reserved.➤ Menu 3 - Remote start Menu Item FeatureOpt. 1Opt. 2 Opt. 3 Opt.4 Opt. 51Transmission ModeManualAu
46© 2008 Directed Electronics. All rights reserved.Feature descriptionsThe features of the system are described below. Features that have additional s
47© 2008 Directed Electronics. All rights reserved.1-3, Horn Function: Turns On/Off the confirmation honks when locking/unlock-ing. Use it to change th
48© 2008 Directed Electronics. All rights reserved.1-8 Comfort Closure Off(1): The system can be programmed to close the win-dows when the system is l
49© 2008 Directed Electronics. All rights reserved.2-2 Valet switch pulse count, 1 pulse. Optional starter kill emergency override. From valet, 2 - 5
5© 2008 Directed Electronics. All rights reserved.Warning! Safety firstThe following safety warnings must be observed at all times:Due to the complexit
50© 2008 Directed Electronics. All rights reserved.2-8 Aux 1 Validity (1) Latched (2), Latch reset w/ignition (3), 30-sec. timed (4) Validity: Output
51© 2008 Directed Electronics. All rights reserved.2-13 Aux 3 Linking None (1) Lock (2) Unlock (3) Lock/Unlock (4) Smart key control (link to remote
52© 2008 Directed Electronics. All rights reserved.3-3 Crank Time 0.6 0.8 (2) 1.0 (3) 1.2 (4) 1.4 (5) 1.6 (6) 1.8 (7) 2.0 (8) 4.0 (9) SECONDS: If the
53© 2008 Directed Electronics. All rights reserved.3-10 Accessory State During Wait-To-Start On: This feature will allow the se-lection of the accesso
54© 2008 Directed Electronics. All rights reserved.➤ Bitwriter® The Bitwriter® has the ability to fine tune certain features of the system. Th
55© 2008 Directed Electronics. All rights reserved.Feature Default settingOptional settingsFeature programming Unlocked LockedTransmitter programming
56© 2008 Directed Electronics. All rights reserved.Shutdown diagnosticsTo perform shutdown diagnostics:With the ignition OFF, press and hold the Valet
57© 2008 Directed Electronics. All rights reserved.Remote starting diagnosticsWhen the remote start function is activated, you can determine the cau
58© 2008 Directed Electronics. All rights reserved.Remote start safety checkBefore vehicle reassembly, the remote start system must be checked to ensu
59© 2008 Directed Electronics. All rights reserved.Troubleshooting➤ Keyless entry systemSystem will not passively lock until it is remotely l
6© 2008 Directed Electronics. All rights reserved.After the remote start module has been installed, test the remote start module in accordance with th
60© 2008 Directed Electronics. All rights reserved.The remote start will activate, but the starter never engages.•Check for voltage on the purple sta
The vehicle starts, but will only run for 10 seconds.•Is the remote start programmed for voltage sense? If this does not work, a 1. tach wire should
N4102V 2008-09Vista, CA 92081www.directed.com© 2008 Directed Electronics—All rights reserved
7© 2008 Directed Electronics. All rights reserved.What is includedThe control module •Control center with integrated status LED and Valet Override sw
8© 2008 Directed Electronics. All rights reserved.➤ D2DThe system has the ability to interface with an XK module through the D2D port. The advantage t
9© 2008 Directed Electronics. All rights reserved.➤ Before beginning the installationPlease read this entire installation guide before beginning the i
Comments to this Manuals