Viper 560XV Installation Guide Page 1

© 2003 Directed Electronics, Inc. Vista, CA N563V 6-03NOTE: This product is intended for installation by a professional installer only!Any attempt to

10 © 2003 Directed Electronics, Inc. Vista, CAThe ignition wire is powered when the key is in the run or start position. This is because the ignition

© 2003 Directed Electronics, Inc. Vista, CA 11An accessory wire will show +12V when the key is in the accessory and run positions. It will not show +1

12 © 2003 Directed Electronics, Inc. Vista, CAThe (+) parking light wire is often found near the switch. Many cars have the switch built into the turn

© 2003 Directed Electronics, Inc. Vista, CA 13Once you have determined the wire color, the easiest place to connect to the wire is often at the kick p

14 © 2003 Directed Electronics, Inc. Vista, CAprimary harness (H1), 12-pin connector__________________________________________________________________

© 2003 Directed Electronics, Inc. Vista, CA 15door lock harness, 3-pin connector__________________remote start ribbon harness, wiring diagram_________

16 © 2003 Directed Electronics, Inc. Vista, CAheavy gauge relay satellite wiring diagram________________________________________________remote start h

© 2003 Directed Electronics, Inc. Vista, CA 17primary harness (H1) wire connection guideThis wire supplies a (-)500 mA ground as long as the system is

18 © 2003 Directed Electronics, Inc. Vista, CAThis input comes from the factory set to 2 activation pulses. This means that it is necessary to have 2

© 2003 Directed Electronics, Inc. Vista, CA 19Most vehicles use negative door trigger circuits. Connect the green wire to a wire which shows ground wh

2 © 2003 Directed Electronics, Inc. Vista, CABitwriter™, Code Hopping™, Doubleguard®, ESP™, FailSafe®, Ghost Switch™, Learn Routine™, Nite-Lite®, Nuis

20 © 2003 Directed Electronics, Inc. Vista, CARemove any paint and connect this wire to bare metal, preferably with a factory bolt rather than your ow

© 2003 Directed Electronics, Inc. Vista, CA 21IMPORTANT! Never use this wire to drive anything but a relay or a low-current input! The transis-torized

22 © 2003 Directed Electronics, Inc. Vista, CAThis wire sends a negative pulse every time the remote start shuts down or the doors are locked. This ca

© 2003 Directed Electronics, Inc. Vista, CA 23relay key switch interface wire connection guideThe five heavy gauge wires coming from the large connect

24 © 2003 Directed Electronics, Inc. Vista, CARemove the two 30-amp fuses prior to connecting these wires and do not replace them until the satellite

© 2003 Directed Electronics, Inc. Vista, CA 25remote start secondary harness (H3) wireconnection guideThis wire supplies a 200mA output as soon as the

26 © 2003 Directed Electronics, Inc. Vista, CAConnect this wire to the provided toggle (override) switch as shown in figure A. Connect the other wire

© 2003 Directed Electronics, Inc. Vista, CA 27According to available information, the only vehicles currently manufactured this way are most General M

28 © 2003 Directed Electronics, Inc. Vista, CAwill allow the customer to turn the key on and shut the remote start down by pressing the brake without

© 2003 Directed Electronics, Inc. Vista, CA 29

© 2003 Directed Electronics, Inc. Vista, CA 3table of contentswarning! safety first . . . . . . . . . . . . . . . . . . . . . . . . 4installation poin

30 © 2003 Directed Electronics, Inc. Vista, CAbypassing GM vehicle anti-theft systems (VATS)Vehicles with the GM VATS (Pass Key) systems have a resist

© 2003 Directed Electronics, Inc. Vista, CA 311995 and newer vehicle anti-theft systems(immobilizers) 1995 and newer vehicle anti-theft systems (immob

32 © 2003 Directed Electronics, Inc. Vista, CAceiver will excite the transponder, which is located (but not visible) in the head of the ignition key.

© 2003 Directed Electronics, Inc. Vista, CA 33shock sensor harness, 4-pin connectorInputs shorter than 0.8 seconds will trigger the Warn Away® respons

34 © 2003 Directed Electronics, Inc. Vista, CAtach learningTo learn the tach signal:1. Start the vehicle with the key.2. Within 5 seconds, press and H

© 2003 Directed Electronics, Inc. Vista, CA 35In most cases, this jumper can be left in the OFF position. Some new vehicles use less than 12 volts in

36 © 2003 Directed Electronics, Inc. Vista, CA3. Choose. Within 10 seconds, press and release the Program switch the number of times cor-responding to

© 2003 Directed Electronics, Inc. Vista, CA 37Learn Routine will be exited if: Door is closed. Ignition is turned off. Program switch is pressed to

38 © 2003 Directed Electronics, Inc. Vista, CAmulti-level security armingMulti-Level Security Arming is a feature that allows the user to select which

© 2003 Directed Electronics, Inc. Vista, CA 39To program the features using the Valet switch:1. Open a door. (The GREEN wire, H1/5, or the VIOLET, H1/

4 © 2003 Directed Electronics, Inc. Vista, CAwarning! safety firstThe following safety warnings must be observed at all times: Due to the complexity

40 © 2003 Directed Electronics, Inc. Vista, CAThe learn routine will be exited if: The door is closed. The ignition is turned on. The Valet/Program

© 2003 Directed Electronics, Inc. Vista, CA 41FEATURE ONE-CHIRP SETTING (DEFAULT) TWO-CHIRP SETTING3-1 Engine checking ON Engine checking OFF3-2 Engin

42 © 2003 Directed Electronics, Inc. Vista, CAfeature descriptionsThe features of the system are described below. Features that have additional settin

© 2003 Directed Electronics, Inc. Vista, CA 431-7 DOOR LOCK PULSE DURATlON: Some European vehicles, such as Mercedes-Benz and Audi, require longer loc

44 © 2003 Directed Electronics, Inc. Vista, CA2-3 NUISANCE PREVENTION CIRCUITRY™ (NPC™) ON/OFF: NPC™ stops repeated triggering of the same zone. Ifone

© 2003 Directed Electronics, Inc. Vista, CA 452-10 CHANNEL 4 VALIDITY/LATCHED/LATCHED RESET WITH IGNITION/30 SECOND TIMED/90 SECOND TIMEDOUTPUT: This

46 © 2003 Directed Electronics, Inc. Vista, CA3-4 PARKING LIGHTS FLASHING/CONSTANT: In the default setting, the unit will flash the vehicle's par

© 2003 Directed Electronics, Inc. Vista, CA 47nuisance prevention circuitry™NPC™ requires that you change the way you test the system as NPC™ will byp

48 © 2003 Directed Electronics, Inc. Vista, CAtimer modeBy pressing the remote and buttons the parking lights will flash 4 times and then start the

© 2003 Directed Electronics, Inc. Vista, CA 49shutdown diagnostics1. With the ignition OFF, press and HOLD the Valet/Program button.2. Turn the igniti

© 2003 Directed Electronics, Inc. Vista, CA 5installation points to rememberIMPORTANT! This product is designed for fuel-injected, automatic transmis

50 © 2003 Directed Electronics, Inc. Vista, CA3. Release the Valet®/Program switch.4. Press and release the Valet®/Program switch within 5 seconds.

© 2003 Directed Electronics, Inc. Vista, CA 51f. Activate the remote start system. If the starter engages, immediately step on the brake to shut dow

52 © 2003 Directed Electronics, Inc. Vista, CA Status LED doesn't work.You've probably guessed already, but here goes: Is it plugged in? (S

© 2003 Directed Electronics, Inc. Vista, CA 532. Was the Tach Learn successful? The LED must light solid and bright to indicate a successful learn.3.

© 2003 Directed Electronics, Inc. Vista, CAORANGE ground when armed outputWHITE (+/-) parking light outputWHITE/BLUE (-) activation inputGREY (-) hood

© 2003 Directed Electronics, Inc. Vista, CA 55relay satellite wiring quick reference guide

6 © 2003 Directed Electronics, Inc. Vista, CAdeciding on component locationsSome things to remember about mounting the siren: Keep it away from heat

© 2003 Directed Electronics, Inc. Vista, CA 7 The higher the control module is in the vehicle, the better the transmitter range will be. If you put t

8 © 2003 Directed Electronics, Inc. Vista, CAIMPORTANT! When the vehicle is delivered, please show the user where this switch is located andhow to dis

© 2003 Directed Electronics, Inc. Vista, CA 9If optional starter kill relay or its connections are immediately visible upon removal of the under-dash