Viper 5902 Installation Guide download pdf (Page 7)

H3/5 GREEN (+) STARTER INPUT (KEY SIDE OF THE STARTER KILL)

H3/6

RED IGNITION 1 +12V INPUT (30A FUSED)

H3/7

PINK/WHITE (30) FLEX RELAY OUTPUT (car side of ign, acc or starter wire)

H3/8

PINK/BLACK (87a) FLEX RELAY INPUT (key side of ign, acc or starter wire if needed)

H3/9

RED/BLACK ACCESSORY/STARTER RELAY +12V INPUT (30A FUSED)

H3/10 NC No Connection

Door Lock, 3-pin connector

1 BLUE (-) 500mA UNLOCK OUTPUT

2 EMPTY NOT USED

3 GREEN (-) 500mA LOCK OUTPUT

Adjusting the Sensor

Important! Make sure the keypad is unlocked and the vehicle is disarmed with no open zones. The on board

shock sensor can be adjusted using the HD remote.

Adjusting the sensor:

Disarm1. the system, turn the ignition Off and close all the doors.

To enter Sensor Adjust, 2. press in and hold the menu wheel (for 3 seconds) on the remote control while

the display is blank. When the

Settings

screen appears, toggle the menu wheel up or down to the

Adjustments

screen and then press in on the menu wheel to enter.

In the 3.

Adjustments

menu, highlight

Sensor Adjust

and press the Menu Wheel. The remote requests the

current setting from the system and displays it in the

Sensor Adjustment

screen.

Follow the on screen instructions to change the setting in the display.4.

Toggle5. the menu wheel up/down or press the

A U X

buttons to change level.

When you have reached the desired level, 6. press and hold the menu wheel, the remote sends the level

setting in the display to the system; a long beep conﬁrms the new level is set. To reset the level to factory

default, press the

A U X

button.

Note: You can test the new setting by cautiously impacting the vehicle with increasing intensity until the

siren chirps, indicating the impact level required to fully trigger the alarm.

Press7. the

A U X

button to exit and return to the

Adjustments

menu. The setting retains the last saved.

To exit the shock sensor adjustment mode from the control module:

Open an entry point or turn on the ignition, the control module emits one long chirp exiting adjustment

mode.

During level setting and level testing if more than 30 seconds lapses without any action the system will exit

sensor adjust and return to the Adjustment menu.

Adjusting the sensor with the 1way remote:

Disarm the system, turn the ignition Off and close all the doors.1.

Press and hold the 2.

A U X

button of the remote control for 8 seconds (If Car 2 mode is on, ignore the Car

Select beep after 3 seconds) or until the amber LED turns on.

Press and hold the 3.

A U X

button 1.5 seconds or until the amber led ﬂashes then comes on solid.- The control

module emits one long chirp, conﬁrming that it has entered adjustment mode.

Press the 4.

A U X

buttons to adjust the sensor level.

Note: You can test the new setting by cautiously impacting the vehicle with increasing intensity until the

siren chirps, indicating the impact level required to fully trigger the alarm.

•

A U X

button: Pressing this button increases the sensitivity one level. The siren chirps twice conﬁrming the

sensitivity adjustment.

•

A U X

button: Pressing this button decreases the sensitivity one level. The siren chirps once conﬁrming the

sensitivity adjustment.

10A FUSE

MINI ATM

RPN: 8540

LIGHT FLASH POLARITY

(10A (MAXIMUM) FUSE JUMPER)

+ -

ELECTRONICS

TACH LEARN THREASHOLD

JMP1 OFF ON

CPU1

NOTE: Pin 1 is on the left

TACH threshold OFF:

TACH threshold ON:

Bitwriter

Port

Neutral Safety

Switch

Remote

Start In

Status

LED

Valet

Port

Door Lock/

Unlock Output

Relay Out

Port

10 9 8 7 6

12345

1 8

1 3

To change

jumper

settings

1 12

1 2 3 4 5 6 7 8 9 10 11 12 ... 22 23

Comments to this Manuals

No comments

Viper 5902 Installation Guide Page 7

Comments to this Manuals

Related products and manuals for Car alarm Viper 5902